AI drafting for plan and profile sheets

AI Plan and Profile Drawing Drafting for Pipelines and Roads

A plan and profile sheet shows the same run of pipe or road twice: from above, along the alignment, and in section, against the ground. Every station, invert, and slope on the profile has to agree with the plan view and with the survey. Nomic drafts plan and profile sheets in CAD from your survey levels, alignment, and design inverts, labels every structure and crossing, and checks slope and cover against the standard you name.

Last reviewed: November 2026

You send

  • Survey levels as a spreadsheet, CSV, or points file
  • The horizontal alignment and stationing
  • Design inverts, structure list, or road grades
  • Your plan and profile sheet template and the design standard

Nomic hands back

  • Plan and profile sheets as DWG with match lines
  • A structure table with stations, rims, and inverts in Excel
  • A list of crossings, cover, and slope issues by station
  • Plotted PDFs with changes clouded and open questions listed
420416412PROPOSED BUILDINGFFE 418.50WWSMH-1RIM 412.30SMH-2RIM 410.85SMH-3RIM 409.12CBCBPROPERTY LINE8" PVC SAN @ 0.50%1ASITE PLANSCALE: 1" = 30'-0"N1234CONSULTING ENGINEERSREVISIONS1ISSUED FOR REVIEWPROJECTMAPLE RIDGE SCHOOLSCALE1" = 30'-0"DATE05/17/2026KEY PLANSHEET TITLESITE PLANSHEET NUMBERC-101

On the sheet

Site Plan, annotated

A civil site plan with contours, the property line, parking, and utilities connecting to the building.

  1. 1Property line
  2. 2Sanitary sewer with manhole rim elevations
  3. 3Water service and storm drain
  4. 4Existing contours with elevations

The problem

Two views of one alignment that have to stay matched

The profile is built from a table of stations and ground levels, often from a survey spreadsheet, then the design line, structures, and labels go on top. Each sheet covers a few hundred feet or meters, with match lines to the next. When an invert changes at one manhole, the slopes on both sides, the cover, and every label downstream change with it, on the profile and in the plan view above it.

Most errors come from drawing the profile and the plan separately: a manhole at one station on the plan and another on the profile, a slope label that was not updated, a crossing with a utility shown on the plan but not on the profile, or cover that dips under the minimum between two structures and nobody notices until review.

01 / Profile

Profiles built from your survey and design levels

Attach the survey levels as a spreadsheet or points file, the alignment, and the design inverts or road grades. Nomic draws the existing ground line, the design line, every structure at its station, and the profile grid and band with stations, levels, and slopes, split into sheets with match lines.

  • Existing ground and design lines plotted from your levels
  • Structures drawn at their stations with rim and invert labels
  • Stations, levels, slopes, and lengths in the profile band
02 / Match

Plan view and profile kept in step

Nomic draws the plan view from the same alignment and stations, so structures, crossings, and match lines line up between the two views. Each utility crossing on the plan appears on the profile with its elevation and the vertical separation, and any you did not give an elevation for is listed.

  • Structures at the same station in plan and profile
  • Utility crossings drawn in profile with vertical separation
  • Crossings with no known elevation listed for potholing
03 / Check

Slope, cover, and separation checked to your standard

Nomic checks every run against the design standard you name: minimum and maximum slope for the pipe size, minimum cover, drops at structures, and separation from water mains. For roads it checks grades and vertical curve lengths. Your civil engineer reviews the flagged runs and signs the sheets.

  • Minimum slope checked for each pipe size
  • Cover checked along the whole run, not only at structures
  • Water and sewer separation checked at every crossing

Checked against

The code and documents behind every sheet

Name the editions the project is designed to and Nomic checks its own drawing against them before handing it back. Your engineer or architect of record makes the final call and stamps the set.

  • Recommended Standards for Wastewater Facilities (Ten States Standards)
  • The local agency or utility design standard
  • AASHTO A Policy on Geometric Design of Highways and Streets
  • State DOT CAD and plan preparation standards
  • The survey control and benchmark on the project

How it works

From a sentence to a stamped set

  1. Step 1

    Ask for the drawing

    Say what the sheet needs to show and attach the backgrounds, markups, cutsheets, or photos. A sentence is enough to start.

  2. Step 2

    Nomic drafts it in CAD

    Nomic works in CAD on its own computer and saves real DWG files to the project, or in your open AutoCAD drawing or Revit model through its add-ins. Either way it uses your layers and blocks and follows how your firm drew the same thing before.

  3. Step 3

    Nomic checks its own work

    The drawing is checked against the code editions you name and the source documents. Everything Nomic drew is clouded, and open questions are listed.

  4. Step 4

    Your team reviews and stamps

    Your engineers and architects review the clouded changes, make the final call, and issue the set under their own stamp.

FAQ

Frequently asked questions

Yes. Nomic drafts plan and profile sheets in CAD from your survey levels, alignment, and design inverts. It draws the ground and design lines, structures, crossings, and the profile band, split into sheets with match lines.

Yes. Attach the survey levels as a spreadsheet, CSV, or points file with stations or chainages. Nomic plots the existing ground line, adds the design line you give it, and labels levels and slopes in the profile band.

No. Your civil engineer sets the alignment, inverts, and grades. Nomic drafts the sheets from them and checks slope, cover, and separation against the standard you name, listing every run that falls outside it.

Nomic saves DWG files that open in Civil 3D and AutoCAD, with the profile drawn as linework, blocks, and text on your layers. If your team keeps the alignment and profile as Civil 3D objects, Nomic can hand back the stations and levels in Excel for your designer to apply.

Both. With the Nomic add-ins for AutoCAD and Revit, the Nomic agent works in the drawing or model your team has open, with your approval before each change. Nomic can also draft on its own computer and save DWG files that open in AutoCAD or any DWG editor.
AI Plan and Profile Drawings: Pipeline and Road Profiles | Nomic