Revit tagging with AI

Automatic Tagging in Revit with AI: Doors, Rooms, and Equipment

Tagging is the part of a Revit sheet that nobody wants and everybody notices. Tag All gets most of the way, and then someone drags tags apart for an hour. With the Nomic add-in, you ask for every untagged door and room on a sheet to be tagged and arranged so nothing overlaps, and Nomic checks the view before it reports back.

Last reviewed: November 2026

You send

  • The Revit model open with the Nomic add-in connected
  • The view or sheet to tag
  • The categories to cover
  • Tag families already loaded in the project

Nomic hands back

  • Tags placed on every untagged element in scope
  • Tags arranged so nothing overlaps
  • A list of categories Nomic could not tag, and why
  • An image check of the view after the change
DOOR SCHEDULEMARKWIDTHHEIGHTTYPEMATLFRAMERATINGHDWREMARKS2013'-6"7'-0"FHMAL1ADA PUSH PLATE2023'-6"7'-0"BHMHM20 MIN4CLOSER, SMOKE GASKET2033'-0"7'-0"BALHM3204A3'-0"7'-0"AALHM90 MIN22053'-0"7'-0"BWDHM32063'-0"7'-0"BWDAL62073'-0"7'-0"BHMHM20 MIN6CLOSER, SMOKE GASKET208A6'-0"7'-0"BHMAL42093'-6"7'-0"AWDHM42103'-0"7'-0"AWDAL62116'-0"7'-0"FHMHM90 MIN4212A3'-0"7'-0"BHMHM20 MIN3CLOSER, SMOKE GASKET2136'-0"7'-0"AALHM1ADA PUSH PLATE2143'-0"7'-0"AWDAL62153'-6"7'-0"BHMHM3216A3'-0"7'-0"BHMHM31ADOOR SCHEDULESCALE: NONE1234CONSULTING ENGINEERSREVISIONS1ISSUED FOR REVIEWPROJECTNORTHGATE MEDICALSCALENONEDATE04/22/2026KEY PLANSHEET TITLEDOOR SCHEDULESHEET NUMBERA-601

On the sheet

Door Schedule, annotated

A door schedule keyed to the plan, with sizes, materials, fire ratings, and hardware sets.

  1. 1Door mark keyed to the floor plan
  2. 2Fire rating for doors in rated walls
  3. 3Remarks with special requirements
  4. 4Revised row, clouded for the reissue

The problem

Tag All is the start of the work, not the end

Placing tags is quick. Making them readable is not. Tags land on top of each other, sit across walls and dimension strings, and point at the wrong door in a crowded corridor. A sheet that looks finished at a distance falls apart at 100 percent zoom.

The cleanup is slow and it repeats. Every time the plan changes, a few tags move, and the pass starts over. It is also the work most likely to be skipped at the end of a week, which is how an untagged door reaches a permit set.

01 / Find

Find what is untagged before placing anything

Nomic reads the view and lists the doors, rooms, and equipment with no tag, using the tag families already loaded in the project. You see what is missing and what Nomic plans to tag, and nothing changes until you approve it.

  • Untagged doors, rooms, and equipment found in the view
  • Tag families already in the project used for each category
  • The plan approved by you before it is applied
02 / Place

Tags placed and arranged so nothing overlaps

Once you approve, Nomic places the tags and moves them off walls, dimension strings, and each other, so every tag can be read and each one points at the right element. The change is one Revit transaction, so one undo takes the whole pass back.

  • Tags placed with the families your project already uses
  • Overlaps with walls, dimensions, and other tags cleared
  • One approval, one undo for the whole pass
03 / Check

The view looked at before Nomic reports

After the change, Nomic captures an image of the view and looks at it. A tag that still overlaps or sits over the wrong element is moved and checked again. What it cannot place, such as a category with no tag family loaded, comes back as an open item for you.

  • An image of the view captured after the change
  • Remaining overlaps fixed and checked again
  • Missing tag families reported, not guessed

Checked against

The code and documents behind every sheet

Name the editions the project is designed to and Nomic checks its own drawing against them before handing it back. Your engineer or architect of record makes the final call and stamps the set.

  • The open model, read before each change
  • Tag families already loaded in the project
  • Your view templates and annotation standards
  • An image of the affected view after each change

How it works

From a sentence to a stamped set

  1. Step 1

    Ask for the drawing

    Say what the sheet needs to show and attach the backgrounds, markups, cutsheets, or photos. A sentence is enough to start.

  2. Step 2

    Nomic drafts it in CAD

    Nomic works in CAD on its own computer and saves real DWG files to the project, or in your open AutoCAD drawing or Revit model through its add-ins. Either way it uses your layers and blocks and follows how your firm drew the same thing before.

  3. Step 3

    Nomic checks its own work

    The drawing is checked against the code editions you name and the source documents. Everything Nomic drew is clouded, and open questions are listed.

  4. Step 4

    Your team reviews and stamps

    Your engineers and architects review the clouded changes, make the final call, and issue the set under their own stamp.

FAQ

Frequently asked questions

Yes, with the Nomic add-in for Revit. Nomic finds untagged doors, rooms, and equipment in a view, places tags with your loaded families, and arranges them so nothing overlaps.

Tag All places the tags. Nomic also moves them off walls, dimension strings, and each other, then captures an image of the view and checks it before it reports back.

Nomic reports the category as an open item instead of guessing. Load the family, or tell Nomic which one to use, and ask again.

Yes. Each approved change is a single Revit transaction, so one undo reverses it.

The Revit add-in is part of the Enterprise plan and is in enterprise preview. Your Nomic account team provides the installer and turns it on for your organization.
Automatic Tagging in Revit with AI | Nomic