AI drafting for construction details

AI Construction Detail Drafting: Wall Sections and Details

Details are where a building is actually decided: how the wall meets the roof, how water leaves the parapet, where the flashing laps. Most come from an office library and get adjusted to the assembly on each job, which is slow work and easy to leave half done. Nomic drafts wall sections and details in CAD from your library, a sketch, or a marked-up photo, sets each layer of the assembly to the wall and roof types on the project, and cites the source for every note.

Last reviewed: November 2026

You send

  • Your detail library as DWG files
  • Wall, roof, and floor type sheets
  • Sketches, marked-up photos, or redlined details
  • The specification sections for the assemblies

Nomic hands back

  • Detail sheets as DWG files in your standards
  • Wall sections drawn to the current assembly types
  • A list of details drawn to a superseded assembly
  • Plotted PDFs with changes clouded and open questions listed
8" CONC. WALL W/ #5 @ 12" O.C. E.F.2" RIGID INSULATION, FULL HEIGHT5" SLAB ON GRADE OVER VAPOR RETARDER24" x 12" CONT. FOOTING W/ (3) #5 CONT.FINISH GRADE1AFOUNDATION WALL SECTIONSCALE: 3/4" = 1'-0"1234CONSULTING ENGINEERSREVISIONS1ISSUED FOR REVIEWPROJECTNORTHGATE MEDICALSCALE3/4" = 1'-0"DATE11/16/2026KEY PLANSHEET TITLEFOUNDATION WALLSECTIONSHEET NUMBERS-501

On the sheet

Foundation Wall Section, annotated

A wall section detail with the footing, reinforcing, insulation, and slab, each called out by a leader note.

  1. 1Footing with reinforcing bars
  2. 2Continuous rigid insulation
  3. 3Slab on grade bearing on the wall
  4. 4Leader notes calling out each material

The problem

A library detail rarely fits the assembly on this job

The office detail for a parapet was drawn for a different wall, a different roof, and a different code edition. On each project someone opens it, changes the insulation thickness, the sheathing, the membrane, and the coping, and renames the notes to match the specification. When the wall type changes after design development, every section that cuts that wall has to change with it, and the ones that do not are the ones a contractor builds.

Small details are drafted under the same time pressure. A roof drain, a slab edge, a stair nosing, a finish transition, or an equipment pad is often a marked-up photo or a hand sketch that someone has to turn into a clean, dimensioned DWG before the sheet can be issued.

01 / Draft

Drafted from your library, a sketch, or a photo

Point Nomic at the library detail, a hand sketch, or a marked-up photo, and name the wall or roof type it belongs to. Nomic draws the detail in CAD with each layer of the assembly at its real thickness, hatches and line weights from your standards, and notes written in the terms your specification uses.

  • Assembly layers drawn at the thickness the wall and roof types call for
  • Hatches, line weights, and text styles from your CAD standards
  • Keynotes and notes tied to the specification sections
02 / Coordinate

Sections that cut the same wall stay in step

Nomic lists every section and detail that cuts each wall and roof type, so a change to an assembly reaches all of them. It checks each against the current type sheet and lists the details still drawn with an old layer, an old thickness, or a note that no longer matches the specification.

  • Every detail that cuts a wall or roof type listed by sheet
  • Details still drawn to a superseded assembly flagged
  • Detail callouts on plans and elevations checked against the detail sheets
03 / Check

Checked against the code and the specification

Before the details go to your architect or engineer, Nomic checks them against the code edition you name and the specification: flashing, weather barrier continuity, fire-rated assemblies, and reinforcement cover. Every change is clouded and every open question is listed for the person who signs the sheet.

  • Flashing and weather barrier continuity checked at each transition
  • Rated assemblies checked against the listed design you name
  • Concrete cover and bar laps checked on reinforcement details

Checked against

The code and documents behind every sheet

Name the editions the project is designed to and Nomic checks its own drawing against them before handing it back. Your engineer or architect of record makes the final call and stamps the set.

  • IBC Chapter 14 exterior walls and flashing
  • IBC Chapter 15 roof assemblies and coping
  • IBC Section 715 joints and voids in rated assemblies
  • ACI 318 concrete cover and development length
  • The listed assemblies and the project specification

How it works

From a sentence to a stamped set

  1. Step 1

    Ask for the drawing

    Say what the sheet needs to show and attach the backgrounds, markups, cutsheets, or photos. A sentence is enough to start.

  2. Step 2

    Nomic drafts it in CAD

    Nomic works in CAD on its own computer and saves real DWG files to the project, or in your open AutoCAD drawing or Revit model through its add-ins. Either way it uses your layers and blocks and follows how your firm drew the same thing before.

  3. Step 3

    Nomic checks its own work

    The drawing is checked against the code editions you name and the source documents. Everything Nomic drew is clouded, and open questions are listed.

  4. Step 4

    Your team reviews and stamps

    Your engineers and architects review the clouded changes, make the final call, and issue the set under their own stamp.

FAQ

Frequently asked questions

Yes. Nomic drafts construction details in CAD from your library, a hand sketch, or a marked-up photo. Each detail comes back as a DWG with assembly layers at their real thickness, your hatches and line weights, and notes tied to the specification.

Yes. Nomic draws wall sections from the wall, floor, and roof types on the project, cut where you call the section on the elevations. When an assembly type changes, Nomic lists every section and detail that cuts it and redraws the ones you approve.

Yes. Attach a hand sketch, a marked-up photo, or a redlined PDF and tell Nomic which assembly it belongs to. Nomic draws a clean, dimensioned DWG and lists any dimension or material the sketch leaves open so you can confirm it.

The architect or engineer who signs the sheet. Nomic drafts and checks the details, clouds every change, and lists open questions. Your team decides what the building is made of and how it goes together.

Both. With the Nomic add-ins for AutoCAD and Revit, the Nomic agent works in the drawing or model your team has open, with your approval before each change. Nomic can also draft on its own computer and save DWG files that open in AutoCAD or any DWG editor.
AI Construction Details: Wall Sections and CAD Details | Nomic