AEC definitions

What Is an Expansion Joint?

Last reviewed: November 2026

An expansion joint is a planned separation between two parts of a structure or pavement that gives them room to expand, contract, and move independently, so the movement does not crack the material or damage the finishes around it.

1234567ABCUNIT501UNIT502UNIT503UNIT504UNIT505UNIT506UNIT507UNIT508AMENITY509UNIT510UNIT511UNIT512UNIT513STAIRS2$a$a$a$a$a$a$a$a$a$a$a$a$aEXIT27'-3"27'-0"27'-3"27'-3"27'-0"27'-3"94'-8"1ALIGHTING PLANSCALE: 1/8" = 1'-0"N1234CONSULTING ENGINEERSREVISIONSPROJECTCEDAR LOFTSSCALE1/8" = 1'-0"DATE02/04/2026KEY PLANSHEET TITLELIGHTING PLANSHEET NUMBERE-201

What you're looking at

Lighting Plan, annotated

A lighting plan with fixtures laid out room by room, switching, and circuit home runs.

  1. 12x4 LED troffer from the fixture schedule
  2. 2Switching zone shared by the fixtures
  3. 3Wall switch at the door
  4. 4Corridor downlights and exit sign
Purpose
Absorb movement from temperature, moisture, settlement, or seismic motion
Depth
A full separation through the element, unlike a control joint
Typical fill
Compressible filler with a sealant, or a manufactured cover assembly
Found in
Buildings, slabs, pavements, masonry, roofs, bridges, and piping
Fire rating
Joints in rated assemblies need a tested fire-resistant joint system
Shown on
Plans, building sections, and joint details

Definition

Expansion joint

Materials change size with temperature, moisture, and load, and a long or restrained element that cannot move builds up stress until it cracks, buckles, or pushes on its neighbor. An expansion joint is the designed answer: a gap that goes through the element, filled with a compressible material or covered with a flexible or sliding assembly. Expansion joints appear in building structures, roofs, facades, masonry walls, concrete slabs and pavements, bridges, and piping. A building expansion joint usually separates the structure into independent sections, which means the joint runs through framing, floors, walls, and finishes and has to be detailed in every layer it crosses.

In depth

Why structures need them

A steel frame grows when it heats and shortens when it cools, and the change adds up along a long building. Concrete shrinks as it cures and dries. Clay masonry slowly expands as it takes up moisture. If the structure is tied to something rigid, the movement becomes stress, and the stress shows up as cracked walls, popped finishes, and sheared connections.

The designer decides where to separate the structure and how much movement each joint must handle. That decision is structural, but its effect reaches the architect’s finishes, the roofing, and every pipe, duct, and conduit that crosses the gap.

Expansion, contraction, isolation, and construction joints

Concrete guidance separates four kinds of joint. An expansion joint is a full-depth gap that lets the elements on both sides move apart and together. A contraction joint, often called a control joint, is a groove or saw cut that weakens the section so shrinkage cracking happens in a straight, planned line, and the slab stays continuous underneath. An isolation joint separates a slab from a column, wall, or footing so they can move independently. A construction joint is where one concrete placement ends and the next begins.

The terms are not interchangeable on drawings. In masonry, clay brick expands over time and needs expansion joints, while concrete masonry shrinks and needs control joints, so the same wall can call for different joints depending on the unit.

How a joint is detailed through a building

A building joint is drawn in plan to show where it runs, in section to show how it crosses the floor, roof, and wall, and in enlarged details to show the cover plates, sealant, backer, and any flashing. The detail changes at each layer: a sliding cover in a corridor floor, a compressible filler and sealant in an exterior wall, and a joint system at the roof, where waterproofing has to bridge the gap.

Fire and sound ratings continue across the gap. The International Building Code requires joints in fire-resistance-rated assemblies to be protected by a fire-resistant joint system, which is tested to ASTM E1966 or UL 2079, so a joint cover alone does not meet the requirement.

Seismic joints are a related case

A seismic joint separates adjacent buildings or building sections by enough distance that they do not hit each other when they sway during an earthquake. The needed width comes from the structural engineer’s calculation of the expected movement of each side, not from the product catalog.

The joint cover has to allow that full movement while keeping the finish surface safe to walk on. This is why joint widths on the structural drawings and the joint product on the architectural drawings need to agree.

Where coordination fails

The common failures are quiet ones. A pipe crosses the joint without a flexible connector. The architectural sheets show a cover that does not match the movement stated in the structure notes. A fire-rated wall crosses the joint with no tested system in the specification. A roof detail stops at the joint line without continuing the waterproofing.

Each of these is visible in the documents before it is built, but it takes someone comparing the structural, architectural, mechanical, and specification sets for the joint locations.

Examples

Expansion joint on a real project

  • 01

    A long concrete parking structure is divided into sections by full-depth expansion joints with sliding deck covers.

  • 02

    A brick veneer wall has vertical expansion joints filled with backer rod and sealant, while the concrete block wall behind it has control joints.

  • 03

    A hospital wing meets an older building at a seismic joint with a cover assembly sized for the structural engineer’s calculated movement.

FAQ

Frequently asked questions

An expansion joint is a planned separation between parts of a structure or pavement that lets them expand, contract, and move independently without cracking or damaging adjacent finishes.

An expansion joint is a full-depth gap that allows movement in both directions. A control joint is a groove or saw cut that creates a planned crack line as concrete or masonry shrinks, and the section remains continuous below it.

An expansion joint is designed to allow movement. A construction joint is where one concrete placement stops and the next begins, and it can be detailed to carry load across it.

When a joint passes through a fire-resistance-rated floor or wall, the International Building Code requires a fire-resistant joint system tested to ASTM E1966 or UL 2079, so the joint does not weaken the assembly rating.

The structural engineer decides the locations based on the building length, the materials, and the expected temperature and seismic movement. They are shown on the structural and architectural plans and described in joint details.
What Is an Expansion Joint? Types, Placement and Details | Nomic